ASME B16.15-2006 pdf free download.Cast Copper Alloy Threaded Fittings Classes 125 and 250.
6 THREADING
6.1 Types of Threads
All pipe fittings shall be threaded with ANSI! ASME 81.201 general purpose pipe threads and shall have taper threads, except wrought couplings (Tables 2 and 1-2). wrought caps (Tables 3 and 1-3). and wrought bushings (Tables 4 and 1-4) in NlS 3(. NPS ) NPS and NPS which may have straight internal threads.
6.2 Tolerances
The permissible tolerance in taper threading shall be limited to one turn large or one turn small from the gaging face on ring and gaging notch on plug, when using working gages. The variations in straight thread- ins shall be limited to one and one-hall turn.s large or small from gaging notch on plug, when using taper pipe thread working gage The reference point br gaging internal fittings threads depends upon the chamfer diameter. When the internal chamfer diameter exceeds the major diameter of the internal thread, the reference point is the last thread scratch on the chamfer cone. When the internal chamfer diameter dees not exceed the major diameter of the internal thread, the reference point is the end of the fitting.
6.3 CountersInk or Chamfer
All internal threads shall not be countersunk a distance of less than one-half the pitch of the thread at an angle of approximately 45deg with the axis of the thread, and all external threads shall be chamfered at an angle of 30 deg to 45 deg with the axis, both for the purpose of easier entrance in making a joint, and for protection of the thread. Countersinking and chamfering shall be concentric with the threads.
6.4 Length of Thread
The length of threads specified in all tables shall be measured to include the countersink or chamfer.
6.5 Alignment
The maximum allowable variation in the alignment of threads of all openings of threaded pipe fittings shall be I mm/rn (0.06 in./fi) or 0.5%.
6.6 BushIngs
All bushings shall be threaded with American National Standard taper pipe threads, except those sues of wmugltt bushings listed in pant. 6.1 which may have straight internal threads. Gaging of all threads shall comply with ANSI/ASME 81.20.1 except those sizes of outside bushings where the external thread lengths are shorter than required by ANSI/ASME 81.20.1. These hLushings should be threaded so that when making up the joint, the shoulder of the head will not interfere. To ensure this, the threads, when made to the minimum length. shall be gaged as listed below with a tolerance of one turn large or small.
(b) NPS 2, I turns large
(c) NI’S 2 to NPS 8 included. 2 Lures large
An outside hushing is one having any part of the hesagon or octagon protruding beyond the outside diameter of the large end of the external thread.
7 RIBS
The addition of ribs or lugs is permitted on threaded pipe fittings. When, ribs are used, it is recommended that their thickness be the same as specified fur the metal thickness of the pipe fitting.
(a) Right-hand couplings shall not have more than two ribs.
(I’) Right- and left-hand couplings shall have four or more ribs Lanless the left-hand opening is clearly marked “1” in which case the use of ribs is optional with the manufacturer.
(c) Wrought couplings do not require opening markings.
8 SURFACE FINISH
Cast pipe fittings shall he furnished with a rough esterior surface, fret of sand inclusions, fins, and gate protrusions
9 FITTING DIMENSIONS
(a) Tables of center-to-end dimensions are given for both straight and reducing pipe fittings. Dimensions and tolerances shown as whole or multiples of 05 mm may differ shghtly in absolute value from the corresponding dimensions in Mandatory Appendix I. Any dimension that is within tolerance by either SI or Customary measurement is considered to be in conformance with this Standard.
(1’) The dimensions shown in Tables 5, 6, 7, 8, and 9 (TaNes 1-5, 1-6, 1-7, 1-8, and 1-9) br fittings are for use only when making patterns for the specific reducing pipe fitting in question and do not apply when a larger size pattern is bushed to make the reducing pipe fitting wanted. Reducing pipe fitting patterns shall be designed to pmduce wall thicknesses and detail and dimensions as required for the sizes involved.